Is water/methanol injection bad for your engine?
Injecting water or methanol through the MAF sensor will likely cause it to short out. Locating the nozzle in front of the turbo chemically alters the turbo compressor map, causing a change in the engine’s air/fuel ratios. Injecting water/methanol directly into the turbo can also damage the compressor blade.
How much HP does water/methanol injection add?
Running the specified Boost Juice through a #6 nozzle with a 5 psi activation point and full on by 12 psi, the water-meth kit improved the power output by as much as 44 hp.
Does methanol add horsepower?
Methanol is a very high octane fuel that is extremely resistant to detonation with an excellent cost/benefit ratio. Its high latent heat of vaporization also makes it an excellent air charge cooler which means a denser mixture and more horsepower.
Do you need to tune for water/methanol injection?
It’s fine. The purpose of re-tuning is to take advantage of the ability to advance timing more with the meth. Otherwise it’s basically just another level of safety since it’s cooling the intake charge.
What can I use for water methanol injection?
What type of fluids can I use with my water methanol injection system? You may use pure water, pure methanol or any mix of the two fluids. Other forms of alcohol such as ethanol, isopropanol, denatured alcohol, etc may also be used.
What do you need to run methanol?
Methanol needs to run at a mixture of about 6.7 to 1 so you will burn about 2 to 2.7 times the volume of fuel. You must have a fuel system capable of flowing high volume. Methanol costs much less than racing gasoline and has a higher octane rating.
Does water/methanol injection work naturally aspirated?
This technology works well on both normally aspirated and boosted engines. Injecting the water/Methanol fluid into a carbureted engine, simply requires spraying the fluid mist into the airstream, upstream of the carburetor(s), or via an injection plate between the carb(s) and the intake.
Can I run methanol injection without a tune?
Meth is 100% ok to run without tuning for it as long as you dont spray too much and cause rich conditions. There are many benefits to your stage 3 tune. You get a nice octane boost with pump gas, lower charge temps, valve cleaning, knock suppression and it helps keep fuel pressure up at lower rpms.
Do you need intercooler with methanol?
Sure there are exceptions to everything, and most people don’t worry about an intercooler when running fuels like M1 Methanol, but in general anything that makes the air intake charge cooler is a good thing. Water Meth vs the Intercooler.
What is included in the water/methanol injection system?
Water/Methanol Injection System, Includes One Gallon Tank/200-PSI Pump, Progressive Pump Controller, Kit Water/Methanol Injection Systems, Stage 1 Boost Cooler, Red Nylon Hose, Kit Water/Methanol Injection System, Stage 2, Carburetor/EFI, Supercharger, Turbocharger, Each
Can I add water/methanol injection without retuning?
Installing water/methanol injection without retuning your engine will usually cost horsepower, as the water replaces some of the combustable air inside the engine. If you can’t advance the timing, increase the boost pressure, or both, don’t bother adding water/methanol injection. If you can, move on to Step 3.
Can I use methanol in my AEM water/methanol injection system?
AEM Water/Methanol Injection Systems are chemically compatible with a mixture of water and methanol, which we strongly recommend does not exceed a concentration of more than 50% methanol. In addition to inherent dangers of using 100% methanol, doing so will damage the system’s flow sensor and void the warranty on this component.
How much does water/methanol injection cost?
Credit more precise engine control systems with making water/methanol injection durable enough for everyday use. Additionally, companies like AEM now offer turnkey, all-inclusive kits for less than $500. Okay, so water/methanol injection is relatively easy to add.
